FLOORING

MM-501

Instant cement with a special formula for leveling floors, increasing floor height or as a work floor before installing ceramics.

MM-501

HOW TO USE

1. Clean the surface from dirt that can reduce adhesion.
2. Pour MM-501 into clean water gradually.
3. Mix ratio: 9-9.5 liter/40 kg. Stir the mixture until smooth.
4. Use a long margin of aluminum steel.
5. If the surface of the brick is too dry, make it wet with clean water.
6. Ketebalan aplikasi yang disarankan adalah 3 mm untuk ukuran keramik maksimum 60 x60 cm.
7. Pot life: 45 – 60 minutes.

WORKING TOOLS
Trowel, long margin steel or aluminum, hand mixer.

BENEFITS

1. Has high adhesion and is plastic when applied.
2. Replace the ceramic without disassembling it.
3. Resistant to expansion and contraction.
4. Strong to withstand compressive loads on the ceramic surface.
5. Avoid popping (loose ceramics).
6. Consistent quality.

SPEAD COVERAGE

± 1,2 m2 / 40 kg / 20 mm

COMPRESSIVE STRENGTH
DIN 18555 Part 3 : 2-5 N/mm2 @28 days
WATER RETENTION
DIN 18555 part 3 : > 95%
DRYING SHRINKAGE
ASTM C 596-01 : < 0,1%

USE
MM-501 can be applied on a variety of surfaces, namely:
1. Solid and level ground
2. Concrete floor surface
3. Rebate floor surface

STORAGE

Store in a closed and dry room. Avoid excessive stacking, maximum 8 stacks per pallet (maximum 2 pallet stacks).

EXPIRED TIME
12 months when stored in closed and dry packaging

EXPOSED FLOOR FLOORING

MM-502

Instant cement with a special formula for leveling floors such as garages, sidewalks, pedestrians, old concrete grading.

MM-502

HOW TO USE

1. Clean the surface from dirt that can reduce adhesion.
2. Pour MM-502 into clean water gradually.
3. Mixture ratio: 4.5-5.0 liter/40 kg. Stir the mixture until smooth.
4. Use a long margin of aluminum steel.
5. If the surface of the brick is too dry, make it wet with clean water.
6. The recommended application thickness is 1-3 cm.
7. Pot life: 20 – 30 minutes

WORKING TOOLS
Iron or steel trowel, long margin of steel or aluminum, hand mixer.

BENEFITS

1. Has a high strength equivalent to the quality of concrete and is plastic when applied
2. Can be used for interior and exterior
3. Has a low expansion and shrinkage
4. Can also be applied on solid ground.
5. Consistent quality.

SPEAD COVERAGE

± 1 m2 / 40 kg / 20 mm

COMPRESSIVE STRENGTH
DIN 18555 Part 3 : 30-35 N/mm2 @28 days
WATER RETENTION
DIN 18555 part 7 : > 95%
DRYING SHRINKAGE
ASTM C 596-01 : < 0,1%

USE
MM-502 can be applied on a variety of surfaces, namely:
1. Solid and level ground
2. Concrete floor surface
3. Rebate floor surface

STORAGE

Simpan di dalam ruangan tertutup, kering, terhindar dari percikan air. Simpan di atas pallet. Hindari tumpukan berlebih, maksimal 10 tumpuk/pallet

EXPIRED TIME
12 months when stored in closed and dry packaging

FLOOR HARDENER

MM-503

Instant cement with a special formula as a scratch-resistant concrete floor coating for parking buildings, workshops, etc.

MM-503

HOW TO USE

1. Above the remaining water on the wet concrete surface, evenly sprinkle 2/3 of the MM-503 material that will be used to cover the concrete surface, leave it until the MM-503 sow becomes wet because it takes the remaining water from the concrete below.
2. Using a wooden trowel or trowel, compact the first layer and remove excess parts so that a flat initial surface is obtained. after 1-2 hours, sprinkle the remaining 1/3 of the MM-503 that has not been sprinkled over the first layer.
3. Do rubbing MM-503 using a trowel carefully, this rubbing process is done repeatedly.

WORKING TOOLS
Trowel

BENEFITS

1. The surface of the concrete floor becomes harder.
2. Resistant to surface friction.
3. The floor does not become slippery and can be used in wet areas.
4. Suitable for warehouse, supermarket, workshop, showroom etc.

SPEAD COVERAGE

± 14 m2 / 40 kg (3 kg/m2)
± 7 m2 / 40 kg (5 kg / m2)
± 5 m2 / 40 kg (7 kg/ m2)

COMPRESSIVE STRENGTH
ASTMC : 50-60 N/mm2 @28 days.

USE
1. MM-503 is used as a surface hardener for concrete floors to be resistant to scratches when passed by light to medium workloads
2. Application of 14 kg/m2 for supermarkets, corridors, pedestrians, carports, etc.
3. Application of 7 kg/m2 for parking area, showroon, workshop etc
4. Application of 5 kg/m2 for factory area, parking area, warehouse etc
5. For the basis of load-bearing strength, still consider the concrete used.

STORAGE

Store in a closed, dry room. Avoid excessive stacks, maximum 8 stacks/pallet (maximum 2 pallet stacks)

EXPIRED TIME
12 months when stored in closed and dry packaging